$4380

Perun
AUG 專用 電子板機 活塞預拉 雙動板機

通用：Tokyo Marui、Classic Army、Army Armament、JG、ASG。

可調扳機靈敏度——扳機可以為第一級和第二級扳機設置 5 個靈敏度級別，範圍從射擊所需的短扳動到長扳機。

無需修改扳機或變速箱，即使在野外也可以改變扳機靈敏度。

可選擇的發射模式——用戶可以選擇短扣或長扣扳機後可用的發射模式：SEMI ONLY、BINARY、SEMI-AUTO、SEMI-BURST、BURST-AUTO。

主動制動 - 主動制動在每次射擊後停止電機，防止彈簧壓縮，或者在高射速的複製品的情況下，過度旋轉（雙發問題）。

Precocking - 快速觸發響應可能是勝利或失敗的問題，尤其是在 CQB 情況下。

啟用預擊發後，每次射擊後活塞將保持在後部位置，彈簧已經壓縮，確保在您扣動扳機後立即發射下一槍。

要在使用預擊發後釋放彈簧，扣動扳機並保持 2 秒，然後將發射第二槍，這次沒有預擊發並且完全制動。

二元扳機 - 允許在半自動設置中輕鬆連發。啟用此模式後，如果設置了半自動射擊，則不僅在扣動扳機時會開火，鬆開時也會開火。

射速降低 - 降低自動或連發射擊的射速以節省彈藥或使復製品以更逼真的方式射擊。低電池電壓警報 - 專用於鋰聚合物和鋰離子電池。

如果電池電壓下降到危險的低水平，將通過每分鐘重複的短聲音信號通知用戶。這也可以自由打開和關閉。

DSG——一種扇形齒輪檢測模式，專門用於雙扇形齒輪。診斷系統 - 持續監控副本和 mosfet 本身。

如果出現任何問題，立即讓您知道可能是什麼問題，從而使故障排除變得更加容易。電子保險絲 - 將在發生重大故障時保存您的複製品和電池。

當檢測到短路或電機阻塞時，它會自動斷開電池。所有設置的編程僅通過使用安裝在電池盒和触發器中的按鈕和多色 LED 二極管完成。

這允許在幾秒鐘內隨時更改設置，即使是在敵人的火力下。

所有設置都是為每個選擇器位置獨立設置的，因此您可以完全按照您想要的方式對 mosfet 進行編程，例如 semi on semi 和 binary trigger on auto。

適用於 P90 的 Perun 可以毫無問題地使用 7 V 至 17 V 的任何電池。它也可以用於最極端的設置 

Adjustable trigger sensitivity – The trigger can be set to 5 sensitivity levels for both first and second trigger stage,

ranging from short pull needed to fire a shot, to a long one.

No modification to the trigger or the gearbox is needed, and the trigger sensitivity change is possible even in the field.
Selectable firing modes – User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY,

SEMI-AUTO, SEMI-BURST, BURST-AUTO.
Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire,

overspin (double shot problem).
Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled,

piston will remain in rear position after each shot with the spring already compressed,

ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking,

pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.
Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode,

if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.
Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.
Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level,

user will be notified by short sound signals that are repeated every minute.

This may also be freely switched on and off.
DSG – a sector gear detection mode specially prepared to work with dual sector gears.
Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.
Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using a button and multicolor LED diode mounted in the battery compartment and the trigger.

That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position,

so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.
Perun for P90 works without problems with any battery from, 7 V to 17 V. It can also be used with most extreme setups.